Posts

Chosen Solution I replaced my cracked iPhone 8 screen with a new screen that I got from Ifixit once I turned the power on my new screen was unresponsive. How can I fix this issue. In the end I had to put the cracked screen that I wanted to replace in order for my touch screen to work… are there any solutions to this issue. Hi Iv seen this happen with a a couple iPod touches and all I had to do was clean the connectors with some 99% isopropyl and this issue went away The isopropyl alcohol helps remove any dirt and debris that our eyes can’t see that could cause the screen not to work properly If that doesn’t work I would contact iFixit customer support to see if they can do anything about the issue Hopefully this helps Any questions please asks Thanks:-)

Chosen Solution I have a Orion TV sled 4668 LED LCD Dhtv that the picture looks blurry @merilynflor blurry pictures are almost exclusively caused by a a bad t-con but can also be caused by a bad panel and bad main board. Remove the back cover from your TV and post some good pictures of your boards etc. That way we can see what you see. Adding images to an existing question If nothing else I’d replace the T-con board first....

Chosen Solution When I try to plug in my phone, (I’ve used the charger it came in plus like eight others), it charges for less than a second, stops charging, charges again, less than a second, stops charging. I’m really panicking here, because it’s already died, can someone help? It looks like a problem with the charging connector bracket witch if it is should just be replaced.

Chosen Solution I seem to be having an issue with the wifi on my laptop. Why is my signal so low when other laptops around me are working so well? First see how far you are from the router. The further away a device is from a router the weaker the connection will be. A way to fix the distance issue, common on houses with two or more floors, is to use a repeater to enhance the signal on the floor without the router....

Chosen Solution I have a M1 Macbook, it had no damages and everything was fine yesterday evening. No trauma or liquid damage afaik as it was just on the desk. Then suddenly it started going black, first it was every minute or so, in that point closing the display and opening it fixed it. Then it started turning off every 30 seconds, same thing closing display and opening again fixed it....

Chosen Solution My Mac is constantly restarting is a loop. If I try to put it in recovery mode or safe mode, it continues the loop . I also get often kernel panics: Do you have an external USB drive you can configure as a bootable drive using a friends Mac? Ideally, you want to set it up with macOS Sierra (10.12.x)

Chosen Solution Hi, Since a few days, when my MacBook Pro is connected to the MagSafe power source and I Log On … Open an app that demands more resources like virtual machine, iPhone simulator in Xcode, etc., The computer stops charging (MagSafe LED goes off) and I have to disconnect from power, wait at least 15-20 seconds and connect it again in order to start charging again. The battery has 724 cycles and Coconut Battery says is in good condition....

Chosen Solution Microsoft Sculpt Comfort keyboard with PCB E170968 94V-0The USB dongle is completely broken the place where the USB prongs are soldered on the PCB has come with the PCB layer itself.Can the controller on the keyboard be replaced by a generic one? Can any generic receiver be paired instead? Hi @wp2020 This is actually a good question, if you search around, there are many people bashing MS about this....

Chosen Solution where can I find mid 2012 macbook air memory upgrade step by step instructions? You cannot upgrade the RAM on a MacBook Air. It is soldered in place. (Src: https://everymac.com/systems/apple/macbo…) If you have the 4 GB model, you can buy a 8GB logic board (MacBook Air 13" (Mid 2012) 1.8 GHz Logic Board) and replace it, using the step-by-step instructions at ifixit. Here is a link: MacBook Air 13" Mid 2012 Logic Board Replacement

Chosen Solution 2015 MacBook Air. Wiped the drive and booted to recovery mode to install new OS. No Hard drive found. Boot into Target Disk and hard drive is there and I can erase and install an OS. Still not hard drive found when I boot to the Air. I have done PRAM reset and SMC. Nothing. Cannot boot into Safe Mode or Single User. I have unseated and reseated the drive....

Chosen Solution Hello . I just purchased macbook air a1237 model. Looks like it is missing screw post and screw located between cpu’s .This screw is holding heat sink as well cpu bracket (v shape ) . Is there way to buy missing post for the screw or fix that some how ? Looks like this mac is overheating now and turns off after few min . See pic below on link http://forums....

Chosen Solution Dear all, I bought my BLU VIVO 5R 2 months ago in Ciudad del Este, Paraguay and my phone is currently not charging at all. It seems like it´s a software problem because sometimes when it´s ON and I plug the power wire it suddenly reboot the mobile phone. And it only charge if it´s OFF, but when you´re using it, the battery drops very fast. BLU Service wants me to send the device to Asunción, PY, or to Montevideo, Uruguay....

Chosen Solution Hi @jp8380 , Don’t turn on the PC, just turn on the monitor and see if you can view the monitor’s OSD (On Screen Display) menus without the monitor powering off and then powering on again. I assume that it powers off and not just that the screen turns off, because you said “… moniter turns off completely and so does the light.”? Is seems as though there is a problem with the power supply connection in the monitor itself....

Chosen Solution My 99 blazer stalls when I put it in reverse I have a 1992 S-10 Blazer that did the same thing. I fixed it by changing out the spark plugs, spark plug wires, and the cap and rotor. The connections tend to get corroded. Is it miss-firing at all? Also, putting a bottle of fuel injector cleaner in the gas tank might help as well.

Chosen Solution My Anker sound pro powers up but no Bluetooth light and can’t find on any device Does your bluetooth work? If it does your light probably just dyed. If your bluetooth does’t work then I would not know more information is needed. Did it just stop working one day, after a fall, fell in to water?

Chosen Solution The disassembly guide does not include the flash disassembly. Could you provide instructions on removing and replacing the flash pop up mechanism? Thanks for your response, but I’m looking for a more specific answer, which is why I left my question on the Fuji x30 product page. Let me be specific: my fujifilm x30’s pop up flash mechanism is broken and the dissasembly guide for this camera doesn’t completely take apart the flash....

Chosen Solution One day it worked and then, moving it from the lecture room to my office, it stopped working. Any help would be appreciated. Hi @h0dg1e_85 Here’s a video that may be of some help to fix the problem

Chosen Solution Hi, I dropped my phone recently and I think the home button broke. How would I go about fixing it? Hello, If your issue is with your home button, you may have damaged something underneath the button. Follow the steps in the Home Button Replacement Guide to get under the home button and see what sort of damage there is. You may just need to replace the button.

Chosen Solution I’m one of Japanese guy so sorry for my bad english I repaired my Imac, but it doesn’t start. As for the power supply, I tryed two other things and verified it, so I think the reason is the logic board. I tryed to short the power button cable to boot, but it didn’t work. It did not work even if I heated the logic board with a heat gun, but LED1 is operating without problems, it seems that it is stuck at startup after pressing the power button....

Chosen Solution My iPhone 5 does not load I changed the load connector of it and persisted with error what should I do What do you mean by the load connector? Do you mean the charge port? If so, change the battery first. If that doesnt help, it’s probably the charge IC that needs to be replaced. This is a board level repair and will require micro soldering experience.