Chosen Solution if I shut off the lights and use a flashlight I can still see the picture. But there is no bright lights to it what can I do to solve this problem? @kristilynne406 this could be a power board issue as well as a backlight array isue. Remove the back of your TV and get a multimeter. You should have a connector on the power board that goes to the LED array....
Chosen Solution Hi. My fan wont turn on after I spilled water on my macbook. Can I change any heat sensor or the fan? Is the fan the only thing that is not working? After opening up the back, you should check the fan connections for any corrosion and clean those off as well as any other connections inside the computer. If those are all clean you can also do an SMC and PRAM reset that may help....
Chosen Solution Hi there! I have a late 2016 MacBook Pro that has probably been used in total 20-30 times. It had sat for somewhere around 6 months without being used/charged at all. Upon going to use it, it did not power on. Obviously, my first course of action was to put it on the charger. After giving it about an hour to charge, I came back to fire it up....
Chosen Solution I was installing mac os by a bootable flash through Recovey Mode. It crashed and reset to where it had crashed before. I boot the mac by holding option key.there were 3 option: the hard drive which was formated, the bootable flash (which i tried that to repeat the installation and crashed again) and a wierd icon. I clicked on that icon, again it showed the bootable flash and the hard drive but in diferent size and resolution....
Chosen Solution I have a 15" mid 2014 MacBook Pro retina (11,2). I was wondering if it would be possible to swap out the logic board to logic board 11,3. I see the only difference is the processor speed, but I don’t know if this works with all components of 11,2 version, and I see the 11,3 version is a little bit less expensive. My Problem: Constant shutdown in MB Pro Retina 11,2....
Chosen Solution Is there a chemical I can use to clean out inside besides vinegar ? What about CLR Manganese leaves brownish or blackish stains. * White vinegar, a weak acid, is about 5 percent acetic acid. It may remove hard water deposits from glass, rust stains from sinks, and tarnish from brass and copper.Lemon juice, another weak acid, contains citric acid, which can be used in much the same way as vinegar....
Chosen Solution When making calls, people cannot hear my voice, though they can hear garbled noises coming through. Having headphones in increases the sound quality to the point where I can be heard and understood, but not as clearly as normal. I have tried using safe mode and the problem was the same. I visited a Cell Phone Repair shop and they quoted me a total of $215 to replace the microphone, because apparently they would have to also replace the screen to do so… so it was two costs (screen and mic), $149 and $65 (I don’t remember which was which, sorry)....
Chosen Solution Hi Accidentally, water spelt in to my Samsung S3 I9300. I took it to a local tech. and he informed me that there is a water damage and he tried his best but failed in getting the device charging back. the device now working properly, accept it doesn’t charge and nothing showing on the screen when connecting it through any kind of charging( i.e. wall charger or through pc)....
Chosen Solution All I am looking for is an answer to how to take this toy apart. I took the basic screws out but it’s still solid as a rock. I tried unscrewing the wheels figuring they would separate. No luck. Some toys just seem to be clicked together internally? I can fix it if I knew how to break the plastic shell open. Help? Anyone know any tricks to doing this?...
Chosen Solution My Blu phone 4 advance has just frozen. when it is powered on it goes to the second screen and does not go any further. Tried to turn it off and it won’t. I did a battery pull and is the same problem. What can I do. hold the power and volume button the same time for ten seconds
Chosen Solution I accidentally ran over a chunk of wood and the mower shut down so I figured I sheared the flywheel key and replaced it and the spark plug with no luck I also sprayed starting fluid into the air filter after taking the filter out and nothing happened it just cranks over very fast but won’t start PLEASE HELP !! Lou C This “I also sprayed starting fluid into the air filter” points to your mower not having a spark....
Chosen Solution MY freezer MUFD19V9KSO stopped working and displayed E5 error code, can any one help me , what’s this code for ? “E5” typically stands for Showroom mode, you can press and hold the “Up” and “Down” keys simultaneously and that should restart your refrigerator back to normal operation.
Chosen Solution Toshiba Portege z30-a broken. I’ve tried everything, like replacing the battery, replacing chargers, nothing works. Not even any reset cycles work. Sometimes, when I reset it and plug it in, it turns on. But only for 2 seconds, then turns off. I’m about to give up on this laptop. MY RTC battery is also low. But Ive heard it’s possible to work a laptop with a dead/low RTC battery....
Chosen Solution Hi. So I have been using my iPhone 6s for over a year now and my phone just blacked out. So basically, I left my phone in a room to charge (The room had air conditioner on, at 24°C). And then after a few hours my phone was not able to turn on. Whenever I hold the power button at the side to see if my phone was actually low battery, no dice....
Chosen Solution It’s says no service and I know I have service. It had some speaker problems a couple days ago. But now they work? And it’s been sluggish too. Taking longer than normal to load videos and such. Could this be signs of needing a new battery? I did some troubling shooting and that didd’t really help? It’s sluggish probably because of the battery this can be checked in settings>Battery>batteryHealth , the service can be a few reasons, the SIM card is faulty, try using another SIM card and see if you get any luck, the network card maybe faulty and needs replacing or the antenna bands on the housing are faulty in which case the housing would need to be replaced....
Chosen Solution My phone is suddenly takingn screenshots when the Home button ism pressed as well as suddenly closing. This is a fault with the power/volume/mute flex invoking random presses. The only real fix for this is to have the flex replaced. I have done lots of these but it isn’t a job for just anyone as it requires almost a complete teardown of the phone. However, the part is very cheap and if you know someone that can do the work it shouldn’t cost much despite how big the job sounds....
Chosen Solution This has been happening a lot lately and it is getting really frustrating. I haven’t changed my screen or anything and I’ve had my Moto G4 for about a year now. I haven’t dropped it from high up or anything and the phone is in great condition. Somehow, most of the time I pick up my phone to use it, the phone will start touching and opening random apps or start typing things when I’m trying to send a text....
Chosen Solution my phone is black but responds with a screenshotting noise and notifications, i haven’t dropped it and it is fully charged? ive checked responses but they have all said that they have been dropped Hi, As a DIY repair all you can do is to open the phone and check if the display flex cable is securely connected to the systemboard and if so then to temporarily replace the display to prove whether the problem is in the display or the systemboard....
Chosen Solution It only shows when its charging and go back to the logo ,doesnt go to safe mode Hold down the power and volume up buttons simultaneously, and when the Samsung logo appears let go. You are now in Recovery Mode. From here you can try clearing cache and then see if it starts. If that doesn’t work, you could try to Factory Reset (WARNING: THIS WILL DELETE ALL OF YOUR PERSONAL DATA AND RESTORE TO FACTORY SETTINGS)....
Chosen Solution Cleaned clogged condensor. Recovered, pulled deep vacuum from high side, h.p.charge in low side to backflush clogged drier. Re-recoverred, evacuated and charged w/ 6.5 oz R-134. Ran OK for three weeks, slightly noisy still but @ -15 deg.F. Problem returned! Suspecting oil slugging compressor and/or clogged drier. Any thoughts???? Second submision: I can’t revise question to make it any clearer! Can I get any feedback? Hi @keithlurken, The only thing that I can suggest is to invest in the service manual, (supplier example only)....
